1 files changed, 11 insertions, 3 deletions

diff --git a/5.-KrakenSDR-Web-Interface-Controls.md b/5.-KrakenSDR-Web-Interface-Controls.md
index 12f7e28..1b9d3bd 100644
--- a/5.-KrakenSDR-Web-Interface-Controls.md
+++ b/5.-KrakenSDR-Web-Interface-Controls.md
@@ -11,11 +11,10 @@ The GUI is used to start and stop the KrakenSDR data acquisition, and to control
 The frequency at the center of the active bandwidth. Changing this frequency and clicking update will trigger the noise source and start the coherence calibration procedure.
 
 **Receiver Gain**
-
+<img src="https://user-images.githubusercontent.com/78108016/171107884-c1e7e627-1108-45a7-9f6e-d18803766d2d.png" width="400" align="right"/>
 The universal gain setting for all five tuners. Check the SNR in the spectrum plot screen, and adjust the gain to achieve high SNR, and to avoid the spectrum overloading.
 
-> **NOTE: Any changes to the center frequency or receiver gain are only applied when the “Update Receiver Parameters” button is pressed.**
-
+> **NOTE: Any changes to the center frequency or receiver gain are only applied when the “Update Receiver Parameters” button is pressed. Pressing Update Receiver Parameters begins a calibration cycle that may take a few seconds to complete.**
 
 ## DoA Configuration
 <img src="https://user-images.githubusercontent.com/78108016/170477435-9876b424-0b5a-4c75-869d-dd52b564192d.png" width="400" align="right"/>
@@ -54,6 +53,8 @@ With a ULA array you will not be able to determine if a target is in front of, o
 If the antenna array is oriented in a way that is not in-line with the vehicles axis of movement, then you can set the offset here. This is most useful for linear arrays that might be oriented along the front-back axis of a vehicle, as zero degrees for a linear array is orthogonal to the array. So in that case it would need to be rotated 90 degrees to be aligned with the vehicles axis of movement.
 
 ## Display options
+<img src="https://user-images.githubusercontent.com/78108016/171108124-34f4eb56-5b68-489a-b87d-90c2498f0a4e.png" width="400" align="right"/>
+
 These options affect the DOA graph display.
 
 **DoA Graph Type**
@@ -64,6 +65,7 @@ Changes between a linear, polar, or compass style plot for displaying DoA bearin
 If you use the compass plot, you can set a compass offset, to compensate for where your array is pointing.
 
 ## VFO Configuration
+<img src="https://user-images.githubusercontent.com/78108016/171108260-d1a26c58-6b41-48ba-9908-c521870c47d9.png" width="400" align="right"/>
 
 Configure properties relating to VFO handling. VFO's allow you to have multiple channels performing direction finding simultaneously within the active 2.4 MHz bandwidth.
 
@@ -103,6 +105,8 @@ If you are looking at very narrowband signals over a small bandwidth, you can us
 If you are squelching on weak, very narrowband CW signal bursts that have pulse periods less than about 50ms this option will help detect them better at the expensive of some computational power.
 
 ## Station Information
+<img src="https://user-images.githubusercontent.com/78108016/171108416-48760218-d4d7-4304-9e9c-f11d1e36a0eb.png" width="400" align="right"/>
+
 This section is for settings specifically about the station and how the station outputs data.
 
 **Station ID**
@@ -134,6 +138,8 @@ If you have a gpsd compatible USB GPS device connected to your Pi 4, you can out
 If you have selected your location source as 'Static', you can enter the latitude, longitude and antenna array heading for your stationary KrakenSDR station.
 
 ## Local Data Recording
+<img src="https://user-images.githubusercontent.com/78108016/171108533-dc567fc0-f85f-4e8b-86a1-276babe12ccc.png" width="400" align="right"/>
+
 If you have no network connection, or no connection to a local Android device you can record DOA data directly to the SD card for later analysis. May be useful for example on a drone.
 
 Logs are written to the `~/krakensdr_doa/krakensdr_doa` folder.
@@ -165,6 +171,8 @@ Monitor this to ensure that the file size does not become huge.
 Downloads the log file from the Web GUI. Note there is a bug with this button as it does not work in the server browser in the KrakenSDR Android App. Please open a standard Chrome browser on your Android device to download the file.
 
 ## VFO Settings
+<img src="https://user-images.githubusercontent.com/78108016/171108614-1d76ccaf-939d-4043-b6e0-bf4a26739e15.png" width="400" align="right"/>
+
 For each VFO channel active there will be one VFO control box. Each box controls the individual VFO settings for Frequency, Bandwidth and Squelch.
 
 **Frequency**