diff options
Diffstat (limited to 'util/_UI/_web_interface/tooltips.py')
-rw-r--r-- | util/_UI/_web_interface/tooltips.py | 210 |
1 files changed, 0 insertions, 210 deletions
diff --git a/util/_UI/_web_interface/tooltips.py b/util/_UI/_web_interface/tooltips.py deleted file mode 100644 index b4ebfd1..0000000 --- a/util/_UI/_web_interface/tooltips.py +++ /dev/null @@ -1,210 +0,0 @@ -import dash_html_components as html -import dash_bootstrap_components as dbc - -dsp_config_tooltips = html.Div([ - # Antenna arrangement selection - dbc.Tooltip([ - html.P("ULA - Uniform Linear Array"), - html.P("Antenna elements placed on a line with having equal distances between each other"), - html.P("UCA - Uniform Circular Array"), - html.P("Antenna elements are placed on circle equaly distributed on 360°")], - target="label_ant_arrangement", - placement="bottom", - className="tooltip" - ), - # Antenna Spacing -# dbc.Tooltip([ -# html.P("When ULA is selected: Spacing between antenna elements"), -# html.P("When UCA is selected: Radius of the circle on which the elements are placed")], -# target="label_ant_spacing", -# placement="bottom", -# className="tooltip" -# ), - # Enable F-B averaging - dbc.Tooltip([ - html.P("Forward-backward averegaing improves the performance of DoA estimation in multipath environment"), - html.P("(Available only for ULA antenna systems)")], - target="label_en_fb_avg", - placement="bottom", - className="tooltip" - ), - ]) - -daq_ini_config_tooltips = html.Div([ - # DAQ buffer size - dbc.Tooltip([ - html.P("Buffer size of the realtek driver")], - target="label_daq_buffer_size", - placement="bottom", - className="tooltip" - ), - # Sampling frequency - dbc.Tooltip([ - html.P("Raw - ADC sampling frequency of the realtek chip")], - target="label_sample_rate", - placement="bottom", - className="tooltip" - ), - # Enable noise source control - dbc.Tooltip([ - html.P("Enables the utilization of the built-in noise source for calibration")], - target="label_en_noise_source_ctr", - placement="bottom", - className="tooltip" - ), - # Enable squelch mode - dbc.Tooltip([ - html.P("Enable DAQ-side squelch to capture burst like signals - NOTE DISABLED IN THIS VERSION, THIS VERSION USES DSP SIDE SQUELCH ONLY")], - target="label_en_squelch", - placement="bottom", - className="tooltip" - ), - # Squelch threshold - dbc.Tooltip([ - html.P("Amplitude threshold used for the squelch feature."), - html.P("Should take values on range: 0...1"), - html.P("When set to zero the squelch is bypassed")], - target="label_squelch_init_threshold", - placement="bottom", - className="tooltip" - ), - # CPI size - dbc.Tooltip([ - html.P("Length of the Coherent Processing Interval (CPI) after decimation")], - target="label_cpi_size", - placement="bottom", - className="tooltip" - ), - # Decimation raito - dbc.Tooltip([ - html.P("Decimation factor")], - target="label_decimation_ratio", - placement="bottom", - className="tooltip" - ), - # FIR relative bandwidth - dbc.Tooltip([ - html.P("Anti-aliasing filter bandwith after decimation"), - html.P("Should take values on range: (0, 1]"), - html.P("E.g.: ADC sampling frequency: 1 MHz (IQ!) , Decimation ratio: 2, FIR relative bandwith:0.25"), - html.P("Resulting passband bandwidth: 125 kHz ")], - target="label_fir_relative_bw", - placement="bottom", - className="tooltip" - ), - # FIR tap size - dbc.Tooltip([ - html.P("Anti-aliasing FIR filter tap size - Do not set too large, or CPU utilization will be 100%"), - html.P("Should be greater than the decimation ratio")], - target="label_fir_tap_size", - placement="bottom", - className="tooltip" - ), - # FIR tap size - dbc.Tooltip([ - html.P("Window function type for designing the anti-aliasing FIR filter"), - html.P("https://en.wikipedia.org/wiki/Window_function")], - target="label_fir_window", - placement="bottom", - className="tooltip" - ), - # Enable filter reset - dbc.Tooltip([ - html.P("If enabled, the memory of the anti-aliasing FIR filter is reseted at the begining of every new CPI")], - target="label_en_filter_reset", - placement="bottom", - className="tooltip" - ), - # Correlation size - dbc.Tooltip([ - html.P("Number of samples used for the calibration procedure (sample delay and IQ compensation)")], - target="label_correlation_size", - placement="bottom", - className="tooltip" - ), - # Standard channel index - dbc.Tooltip([ - html.P("The selected channel is used as a reference for the IQ compensation")], - target="label_std_ch_index", - placement="bottom", - className="tooltip" - ), - # Enable IQ calibration - dbc.Tooltip([ - html.P("Enables to compensate the amplitude and phase differences of the receiver channels")], - target="label_en_iq_calibration", - placement="bottom", - className="tooltip" - ), - # Gain lock interval - dbc.Tooltip([ - html.P("Minimum number of stable frames before terminating the gain tuning procedure")], - target="label_gain_lock_interval", - placement="bottom", - className="tooltip" - ), - # Require track lock intervention - dbc.Tooltip([ - html.P("When enabled the DAQ firmware waits for manual intervention during the calibraiton procedure"), - html.P("Should be used only for hardave version 1.0")], - target="label_require_track_lock", - placement="bottom", - className="tooltip" - ), - # Amplitude calibraiton mode - dbc.Tooltip([ - html.P("Amplitude difference compensation method applied as part of the IQ compensation"), - html.P("default: Amplitude differences are estimated by calculating the cross-correlations of the channels"), - html.P("disabled: Amplitude differences are not compensated"), - html.P("channel_power: Ampltiude compensation is set in a way to achieve equal channel powers")], - target="label_amplitude_calibration_mode", - placement="bottom", - className="tooltip" - ), - dbc.Tooltip([ - html.P("When periodic calibration track mode is selected the firmware regularly turn on the noise source for a short burst to\ - check whether the IQ calibration is still valid or not. In case the calibrated state is lost, the firmware automatically\ - initiates a reclaibration procedure")], - target="label_calibration_track_mode", - placement="bottom", - className="tooltip" - ), - - # Calibration frame interval - dbc.Tooltip([ - html.P("Number of data frames between two consecutive calibration burst. Used when periodic calibration mode is selected")], - target="label_calibration_frame_interval", - placement="bottom", - className="tooltip" - ), - # Calibration frame burst size - dbc.Tooltip([ - html.P("Number of calibration frames generated in the periodic calibration mode")], - target="label_calibration_frame_burst_size", - placement="bottom", - className="tooltip" - ), - # Amplitude tolerance - dbc.Tooltip([ - html.P("Maximum allowed amplitude difference between the receiver channels")], - target="label_amplitude_tolerance", - placement="bottom", - className="tooltip" - ), - # Phase tolerance - dbc.Tooltip([ - html.P("Maximum allowed phase difference between the receiver channels")], - target="label_phase_tolerance", - placement="bottom", - className="tooltip" - ), - # Maximum sync fails - dbc.Tooltip([ - html.P("Maximum allowed consecutive IQ difference check failures before initiating a recalibration")], - target="label_max_sync_fails", - placement="bottom", - className="tooltip" - ), - ]) - - |