diff options
Diffstat (limited to '')
| -rw-r--r-- | _ont/ont-d-link-dpn-100-rev-a2.md | 2 | ||||
| -rw-r--r-- | _ont/ont-fs-com-gpon-onu-stick-with-mac.md | 1 | ||||
| -rw-r--r-- | _ont/ont-halny-hl-gsfp.md | 2 | ||||
| -rw-r--r-- | _ont/ont-huawei-ma5671a.md | 3 | ||||
| -rw-r--r-- | _ont/ont-sercomm-fg1000b-11.md | 1 | ||||
| -rw-r--r-- | _ont/ont-t-w-tw2362h-cdel.md | 2 | ||||
| -rw-r--r-- | _ont/ont-technicolor-afm0002.md | 8 | ||||
| -rw-r--r-- | _ont/ont-technicolor-afm0003.md | 8 | ||||
| -rw-r--r-- | _ont/ont-technicolor.md | 2 | ||||
| -rw-r--r-- | _ont/ont-zisa-op151s.md (renamed from _ont/ont-ziza-op151s.md) | 15 | ||||
| -rw-r--r-- | _ont/ont-zisa.md (renamed from _ont/ont-ziza.md) | 2 | ||||
| -rw-r--r-- | _ont/ont-zte-f6005v3.md | 369 | ||||
| -rw-r--r-- | _ont/ont-zyxel-pmg3000-d20b.md | 2 |
13 files changed, 394 insertions, 23 deletions
diff --git a/_ont/ont-d-link-dpn-100-rev-a2.md b/_ont/ont-d-link-dpn-100-rev-a2.md index 5328863..457d3f5 100644 --- a/_ont/ont-d-link-dpn-100-rev-a2.md +++ b/_ont/ont-d-link-dpn-100-rev-a2.md @@ -36,7 +36,7 @@ Once you access the stick via ssh you will be presented with a second tier login - [Zyxel PMG3000-D20B](/ont-zyxel-pmg3000-d20b) - [Halny HL-GSFP](/ont-halny-hl-gsfp) -- [Ziza OP151s](/ont-ziza-op151s) +- [Zisa OP151s](/ont-zisa-op151s) - [T&W TW2362H-CDEL](/ont-t-w-tw2362h-cdel) # GPON/OMCI settings diff --git a/_ont/ont-fs-com-gpon-onu-stick-with-mac.md b/_ont/ont-fs-com-gpon-onu-stick-with-mac.md index 9894bac..c813e5a 100644 --- a/_ont/ont-fs-com-gpon-onu-stick-with-mac.md +++ b/_ont/ont-fs-com-gpon-onu-stick-with-mac.md @@ -537,6 +537,7 @@ The FS stick stores the content of the emulated EEPROM in U-Boot env variables t - [General setting of lantiq](https://forum.fibra.click/d/23881-ma5671a-e-vodafone-25-gbps/64) - [Usage GPON module SFP in Spain](https://forum.mikrotik.com/viewtopic.php?t=116364&start=300) - [SourcePhotonics SPS-34-24T-HP-TDFO Datasheet](https://www.sourcephotonics.com/wp-content/uploads/2017/08/DS-8085-02_SPS-34-24T-HP-TDFO.pdf) +- [FS.com GPON-ONU-34-20BI Configuration Guide](https://resource.fs.com/mall/doc/20230831180515egrzs6.pdf) --- diff --git a/_ont/ont-halny-hl-gsfp.md b/_ont/ont-halny-hl-gsfp.md index 6756891..423cdcd 100644 --- a/_ont/ont-halny-hl-gsfp.md +++ b/_ont/ont-halny-hl-gsfp.md @@ -37,7 +37,7 @@ parent: HALNy - [Zyxel PMG3000-D20B](/ont-zyxel-pmg3000-d20b) - [D-LINK DPN-100-Rev-A2](/ont-d-link-dpn-100-rev-a2) -- [Ziza OP151s](/ont-ziza-op151s) +- [Zisa OP151s](/ont-zisa-op151s) - [T&W TW2362H-CDEL](/ont-t-w-tw2362h-cdel) ## List of partitions diff --git a/_ont/ont-huawei-ma5671a.md b/_ont/ont-huawei-ma5671a.md index 6152c2e..82e930d 100644 --- a/_ont/ont-huawei-ma5671a.md +++ b/_ont/ont-huawei-ma5671a.md @@ -119,6 +119,7 @@ For more info [XPONos partition layout](https://github.com/XPONos/linux_lantiq-f - [1224abort.bin](https://ma5671a.s3.nl-ams.scw.cloud/1224ABORT.bin){: .btn } md5hash: 10e94a4b4acdc82dec20c7904b69e5c0 - [right.com.cn (China) 19 July 2022](https://mega.nz/file/9fpSkYTb#wNyjAj1kOLWC9HozX-gTQ-TS3VFqRYg--x1rm7RSuDg){: .btn } md5hash: 6b5e7e3c659fe3f0204340fa746ac4fc - [right.com.cn (China) 29 Aug 2022](https://mega.nz/file/VHFFSBrT#2WhDPcdON5EHR01l6Ut35GC3sl55e4l09Z0NUo_7SWA){: .btn} md5hash: 3d357e2dc7b59c66fe61b4ddf1fb8dc0 +- [right.com.cn (China) 20 Nov 2023](https://mega.nz/file/8vcwyJRA#yuzjyI9Y9vsA0RegGnNOy_JLv2FNRIMfI5JxHn8t0-s){: .btn} md5hash: 4901ae8e70991ca1202bc80db9c151cc - [FS.com GPON ONU Stick with MAC firmware / SourcePhotonics SPS-34-24T-HP-TDFO firmware](/ont-fs-com-gpon-onu-stick-with-mac) # Usage @@ -393,4 +394,4 @@ The Huawei MA5671A stores the content of the emulated EEPROM in U-Boot env varia --- -[^subunit]: The subunit are 10000 times smaller than the specified unit
\ No newline at end of file +[^subunit]: The subunit are 10000 times smaller than the specified unit diff --git a/_ont/ont-sercomm-fg1000b-11.md b/_ont/ont-sercomm-fg1000b-11.md index b5db0fb..ed9c46d 100644 --- a/_ont/ont-sercomm-fg1000b-11.md +++ b/_ont/ont-sercomm-fg1000b-11.md @@ -333,6 +333,7 @@ It seems `cmld_client get` can't return string values longer than 12 characters, - 1&1 Glasfaser Modem - Telekom Glasfaser Modem 2 + - Vodafone Glasfaser Modem (FG1000B.VF) # Credits This whole documentation here was made possible thanks to the time invested into reverse engineering by @hwti and the rest of the folks from the forum mentioned in the links section of this page. Thanks a lot! diff --git a/_ont/ont-t-w-tw2362h-cdel.md b/_ont/ont-t-w-tw2362h-cdel.md index 196b4b0..fa588d5 100644 --- a/_ont/ont-t-w-tw2362h-cdel.md +++ b/_ont/ont-t-w-tw2362h-cdel.md @@ -1,7 +1,7 @@ --- title: T&W TW2362H-CDEL has_children: false -redirect_to: /ont-ziza-op151s +redirect_to: /ont-zisa-op151s layout: default parent: T&W ---
\ No newline at end of file diff --git a/_ont/ont-technicolor-afm0002.md b/_ont/ont-technicolor-afm0002.md index deecb29..1958493 100644 --- a/_ont/ont-technicolor-afm0002.md +++ b/_ont/ont-technicolor-afm0002.md @@ -1,8 +1,8 @@ --- -title: Technicolor AFM0002 +title: Vantiva AFM0002 (formerly Technicolor AFM0002) has_children: false layout: default -parent: Technicolor +parent: Vantiva (formerly Technicolor) alias: HiSense LTE3415-SCA+ --- @@ -10,7 +10,7 @@ alias: HiSense LTE3415-SCA+ | | | | ---------------- | ----------------------------------------------- | -| Vendor/Brand | Technicolor | +| Vendor/Brand | Vantiva (formerly Technicolor) | | Model | AFM0002TIM/FWB/WND | | ODM | HiSense | | ODM Product Code | LTE3415-SCA+ | @@ -37,7 +37,7 @@ alias: HiSense LTE3415-SCA+ The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be accessed from the top surface. To accept TX line commands, the GND of the TTL adapter should be attached to the stick's shield: -{% include image.html file="ont-leox-lxt-010s-h_ttl.jpg" alt="Technicolor AFM0002 TTL Pinout" caption="Technicolor AFM0002 TTL Pinout" %} +{% include image.html file="ont-leox-lxt-010s-h_ttl.jpg" alt="Vantiva (formerly Technicolor) AFM0002 TTL Pinout" caption="Vantiva (formerly Technicolor) AFM0002 TTL Pinout" %} {% include alert.html content="Some USB TTL adapters label TX and RX pins the other way around: try to swap them if the connection doesn't work." alert="Note" icon="svg-warning" color="yellow" %} diff --git a/_ont/ont-technicolor-afm0003.md b/_ont/ont-technicolor-afm0003.md index 625f752..fd69c6a 100644 --- a/_ont/ont-technicolor-afm0003.md +++ b/_ont/ont-technicolor-afm0003.md @@ -1,8 +1,8 @@ --- -title: Technicolor AFM0003 +title: Vantiva AFM0003 (formerly Technicolor AFM0003) has_children: false layout: default -parent: Technicolor +parent: Vantiva (formerly Technicolor) alias: HiSense LTE3415-SH+ --- @@ -10,7 +10,7 @@ alias: HiSense LTE3415-SH+ | | | | ---------------- | ----------------------------------------------- | -| Vendor/Brand | Technicolor | +| Vendor/Brand | Vantiva (formerly Technicolor) | | Model | AFM0003TIM | | ODM | HiSense | | ODM Product Code | LTE3415-SH+ | @@ -36,7 +36,7 @@ alias: HiSense LTE3415-SH+ The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be accessed from the top surface. To accept TX line commands, the GND of the TTL adapter should be attached to the stick's shield: -{% include image.html file="ont-leox-lxt-010s-h_ttl.jpg" alt="Technicolor AFM0003 TTL Pinout" caption="Technicolor AFM0003 TTL Pinout" %} +{% include image.html file="ont-leox-lxt-010s-h_ttl.jpg" alt="Vantiva (formerly Technicolor) AFM0003 TTL Pinout" caption="Vantiva (formerly Technicolor) AFM0003 TTL Pinout" %} {% include alert.html content="Some USB TTL adapters label TX and RX pins the other way around: try to swap them if the connection doesn't work." alert="Note" icon="svg-warning" color="yellow" %} diff --git a/_ont/ont-technicolor.md b/_ont/ont-technicolor.md index 046a2f2..e7e3ec0 100644 --- a/_ont/ont-technicolor.md +++ b/_ont/ont-technicolor.md @@ -1,5 +1,5 @@ --- -title: Technicolor +title: Vantiva (formerly Technicolor) has_children: true layout: default ---
\ No newline at end of file diff --git a/_ont/ont-ziza-op151s.md b/_ont/ont-zisa-op151s.md index cb79345..afd9948 100644 --- a/_ont/ont-ziza-op151s.md +++ b/_ont/ont-zisa-op151s.md @@ -1,15 +1,15 @@ --- -title: Ziza OP151S +title: Zisa OP151S has_children: false layout: default -parent: Ziza +parent: Zisa --- # Hardware Specifications | | | | ---------------- | ---------------------------------------------------------- | -| Vendor/Brand | Ziza | +| Vendor/Brand | Zisa | | Model | OP151S | | ODM | T&W | | ODM Product Code | TW2362H-CDEL | @@ -30,9 +30,7 @@ parent: Ziza | Serial encoding | 8-N-1 | | Form Factor | miniONT SFP | -{% include image.html file="op151s.png" alt="Ziza OP151S" caption="Ziza OP151S" %} -{% include image.html file="tw236h-cdel-th.jpg" alt="PMG3000-D20B Teardown" caption="PMG3000-D20B Teardown" %} -{% include image.html file="tw236h-cdel-th-back.jpg" alt="PMG3000-D20B Teardown" caption="PMG3000-D20B Teardown" %} +{% include image.html file="op151s.png" alt="Zisa OP151S" caption="Zisa OP151S" %} ## Serial @@ -46,9 +44,10 @@ The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be a - [Halny HL-GSFP](/ont-halny-hl-gsfp) - [D-LINK DPN-100-Rev-A2](/ont-d-link-dpn-100-rev-a2) -- [Ziza OP151s](/ont-ziza-op151s) +- [Zisa OP151s](/ont-Zisa-op151s) - [T&W TW2362H-CDEL](/ont-t-w-tw2362h-cdel) # Miscellaneous Links -- [Tech Info Depot Wiki](http://en.techinfodepot.shoutwiki.com/wiki/ZISA_OP151S)
\ No newline at end of file +- [Tech Info Depot Wiki](http://en.techinfodepot.shoutwiki.com/wiki/ZISA_OP151S) +- [Zisa OP151S 1GE GPON SFU SFP module](https://www.zisacom.com/admin/ewebeditor/uploadfile/20181116154842842.pdf)
\ No newline at end of file diff --git a/_ont/ont-ziza.md b/_ont/ont-zisa.md index 60af790..e61b01a 100644 --- a/_ont/ont-ziza.md +++ b/_ont/ont-zisa.md @@ -1,5 +1,5 @@ --- -title: Ziza +title: Zisa has_children: true layout: default ---
\ No newline at end of file diff --git a/_ont/ont-zte-f6005v3.md b/_ont/ont-zte-f6005v3.md new file mode 100644 index 0000000..e5a4664 --- /dev/null +++ b/_ont/ont-zte-f6005v3.md @@ -0,0 +1,369 @@ +--- +title: ZTE F6005v3 +has_children: false +layout: default +parent: ZTE +--- + +# Hardware Specifications + +| | | +| ------------ | ----------------------------------------------------------------- | +| Vendor/Brand | ZTE | +| Model | F6005v3 | +| ODM | ✅ | +| CPU | ZTE ZX279133@Dual-Core A53 | +| CPU Clock | 1200MHz | +| Chipset | ZTE ZX279133 | +| Flash | 128 MB (SPI NAND FM25S01A) | +| RAM | 128 MB | +| System | Customized Linux by ZTE | +| 2.5GBaseT | Yes | +| Optics | SC/APC | +| IP address | 192.168.1.1 | +| Web Gui | ✅ user `admin`, password `admin` or defined by ISP | +| SSH | N/A | +| Telnet | ✅ [^1] | +| Serial | ✅ [^2] | +| Form Factor | ONT | + +{% include image.html file="f6005v3_tim_1.jpg" alt="F6005v3 TIM" caption="F6005v3 TIM" %} + +{% include image.html file="f6005v3_of_1.jpg" alt="F6005v3 OpenFiber" caption="F6005v3 OpenFiber" %} + + +## List of software versions +### HW V3.0 +- V3.0.10P3N2 (OpenFiber) +- V3.0.10N06 (TIM Italy) - Internal version is V3.0.10P2N6 + +## List of partitions + +### HW V3.0 + +| dev | size | erasesize | name | +| ---- | -------- | --------- | ---------------- | +| mtd0 | 08000000 | 00020000 | "whole flash" | +| mtd1 | 00300000 | 00020000 | "uboot" | +| mtd2 | 00400000 | 00020000 | "others" | +| mtd3 | 00400000 | 00020000 | "parameter tags" | +| mtd4 | 00400000 | 00020000 | "wlan" | +| mtd5 | 00800000 | 00020000 | "usercfg" | +| mtd6 | 00400000 | 00020000 | "middle" | +| mtd7 | 02a00000 | 00020000 | "kernel1" | +| mtd8 | 02a00000 | 00020000 | "kernel2" | +| mtd9 | 02500000 | 00020000 | "rootfs1" | +| mtd10 | 029e0000 | 00020000 | "rootfs2" | + + +This ONT supports dual boot, as visible from the presence of `kernel0` and `kernel1`, which contain the rootfs (JFFS2 read-only). +The boot images can be swapped if they are the same or use the same **U-Boot** version. If you have a different **U-Boot** that was paired with the active image, do not attempt this, as it will brick the ONT, specially if TTL console is disabled. + +```sh +upgradetest switchver X +``` + +Where `X` can be `0/1`, based on the image you want to boot from. + +Get current installed version for each region: + +```sh +upgradetest getver +``` + +You can also clone the currently running image into the other slot using this command: + +```sh +syn_version +``` + +You can check currenlty running image using this command: + +```sh +# cat /proc/csp/versionstates + +baseaddress : 0x1b00000 +current : 0 +version1states : 0x83 +version2states : 0x83 +____________________________________________________ +Index Running Latest CRC Integrality Type +---------------------------------------------------- +0 Y Y N Y Upg +1 N Y N Y Upg +---------------------------------------------------- +``` + +And check if the backup image has a valid CRC: + +```sh +# upgradetest bakver +backup version crc is ok +success! +``` + + +# Use +{% include alert.html content="Commands have been tested on V3 HW rev. on OpenFiber and TIM firmwares" alert="Note" icon="svg-info" color="blue" %} + +## Enable Telnet +{% include alert.html content="This is an external script ([ZTE ONU Telnet Enabler](https://github.com/stich86/zteOnu)), use at your own risk! Credentials don't survive at reboot!" alert="Note" icon="svg-info" color="blue" %} + +```sh +./zteOnu -i 192.168.1.1 -u admin -p admin +``` + +If Telnet is not opening, you are probably running a newer firmware, in that case change mac-address of the NIC connected to the ONT to `00:07:29:55:35:57` and use the flag `--new`: + +```sh +./zteOnu -i 192.168.1.1 -u admin -p admin --new +``` + +You should get this output and credentials to login over telnet: + +```sh +ZteONU 0.0.7, built at 09/10/2024 +source: https://github.com/stich86/zteOnu +----------------------------------- +step [0] reset factory: ok +step [1] request factory mode: ok +step [2] send sq: ok +step [3] check login auth with user: ok +step [4] enter factory mode: ok +----------------------------------- +Success authenticated with user: admin and password: admin +Telnet Credentials (!! Temporary !!) +User: 9qNBo58H +Pass: OUBToR8J +``` + +## Enable console redirection + +To see omcidebug messages on telnet, execute this command (just the first time of each connection): + +```sh +redir printf +``` + +# GPON ONU status + +## Getting the operational status of the ONU + +To check the connection status, use the following command: +``` +gpontest -gstate +``` +`[gpontest] gpon state is [O5]` for O5 state + +## Getting OLT vendor information + +```sh +sendcmd 132 omcidebug showmedata 131 +``` + +This command will print the following output: + +```sh +################################## +MIB INFO: + ME CLASS: 131 + DB NAME: olt_g, DBHandle: 32 +################################## + +<-----MeID[ 0x0000,0 ], Addr[ 0x19a2b1]-----> + Vendorid:48 57 54 43 + EquipmentID:00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 00 00 00 00 00 00 + Version:31 30 00 00 00 00 00 00 00 00 + 00 00 00 00 + TimeofDay:00 00 00 00 00 00 00 00 00 00 + 00 00 00 00 +--------------------------------------------------------------------- +``` + +## Querying a particular OMCI ME + +```sh +sendcmd 132 omcidebug showmedata ID_MIB (eg. 7 for Firmware version) +``` + +This command will print the following output: + +```sh + +################################## +MIB INFO: + ME CLASS: 7 + DB NAME: soft_image, DBHandle: 14 +################################## + +<-----MeID[ 0x0000,0 ], Addr[ 0x19a011]-----> + Version:V3.0.10P3N2 + Is committed:01 + Is active:01 + Is valid:01 + +<-----MeID[ 0x0001,1 ], Addr[ 0x19a031]-----> + Version:V3.0.10P2N6 + Is committed:00 + Is active:00 + Is valid:01 +--------------------------------------------------------------------- +``` + +# GPON/OMCI settings + +## Setting ONU GPON Serial Number + +{% include alert.html content="Both S/N and VID have to be changed. 2176 is for the VID (first 4 letters of the S/N) and 2177 is for the last 8 digits of the S/N" alert="Note" icon="svg-info" color="blue" %} +```sh +setmac 1 2176 ZTEG +setmac 1 2177 AABBCCDD +``` + +## Setting ONU GPON PLOAM password + +{% include alert.html content="The PLOAM password is stored in the ASCII format." alert="Note" icon="svg-info" color="blue" %} +This can be done easily via the Web UI. To do it via the shell use: +```sh +setmac 1 2181 1234567890 +setmac 1 2178 1234567890 +``` + +## Setting ONU GPON Equipment ID + +```sh +setmac 1 32770 "5::F6005V3.0:" +``` + +## Check Images CRC + +```sh +upgradetest bakver + +backup version crc is ok +success! + +``` + +## Persistent Telnet access + +{% include alert.html content="This procedure was only tested on OF V3.0.10P3N2 and TIM V3.0.10N06 firmware and it's persistent after an upgrade from OLT" alert="Note" icon="svg-info" color="blue" %} + +{% include alert.html content="If you change GPON Serial Number, Telnet will be disabled. You have to run again the tool to enable it" alert="Note" icon="svg-warning" color="red" %} + +Needed tools: + +[ZTE ONU Telnet Enabler](https://github.com/stich86/zteOnu) + +Just run the enabled with `--telnet` flag to make Telnet persisten across Reboot (use `--new` flags and changed mac-address for newer firmware): + +```sh +./zteOnu -i 192.168.1.1 -u admin -p admin --telnet +``` + +```sh +ZteONU 0.0.7, built at 09/10/2024 +source: https://github.com/stich86/zteOnu +----------------------------------- +step [0] reset factory: ok +step [1] request factory mode: ok +step [2] send sq: ok +step [3] check login auth with user: ok +step [4] enter factory mode: ok +----------------------------------- +Success authenticated with user: admin and password: admin +Permanent Telnet succeed +User: root +Pass: Zte521 +Wait reboot.. or powercycle it +``` + +The ONT will reboot, and you can log in later using `root\Zte521` as the credentials. + +**Only for firmware versions with restricted admin access** + +In case you want add new a admin user instead of using the embedded credentials, run these commands before rebooting the ONT: + +```sh +sendcmd 1 DB set DevAuthInfo 5 Enable 1 +sendcmd 1 DB set DevAuthInfo 5 User superadmin +sendcmd 1 DB set DevAuthInfo 5 Pass superadmin +sendcmd 1 DB set DevAuthInfo 5 Level 1 +sendcmd 1 DB set DevAuthInfo 5 AppID 1 +sendcmd 1 DB saveasy +``` + +Reboot the ONT and you can login to the WebUI using `superadmin\superadmin` as credentials with full unlocked menus. + +# Advanced settings + +## Backing up ONT partitions using hardware flasher + +It's possible to swap RAW dump between ONTs and enable access over Telnet to modify some ONT parameters. + +Needed tools: + +- Windows, Linux or macOS with [SNANDer](https://github.com/McMCCRU/SNANDer) +- [CH341a programmer with 3.3V voltage](https://it.aliexpress.com/item/1005004637577204.html?spm=a2g0o.productlist.main.1.21ad51c1Lmyq6Z&algo_pvid=0aade75d-7f57-4fe7-b0f4-b3f2f56af9f1&algo_exp_id=0aade75d-7f57-4fe7-b0f4-b3f2f56af9f1-0&pdp_npi=4%40dis%21EUR%214.25%214.25%21%21%214.56%214.56%21%4021039cc717284006273332970e47ea%2112000029927819932%21sea%21IT%211864988329%21X&curPageLogUid=Xuv1aOCo58M9&utparam-url=scene%3Asearch%7Cquery_from%3A) +- [Pogo-Pin Probe for WSON8 8x6mm chip](https://it.aliexpress.com/item/1005006666230520.html?spm=a2g0o.order_list.order_list_main.21.11e236965SstMd&gatewayAdapt=glo2ita) + +Connect all needed cable from the probe to the programmer, then attach the probe to the chip (use some rubbers to make it stable) and run this command to dump the NAND: + +```sh +/SNANDer -r f6005v3_dump_X.bin +``` + +Do at least 3 dumps and compare their md5 to be sure that are good. + +If you want to flash this dump to another ONT, just run these commands: + +```sh +/SNANDer -e +/SNANDer -w f6005v3_dump_X.bin -v +``` +``` + +## Changing region code + +{% include alert.html content="Be aware that changing the region code may break features such as PPPoE depending on your ISP, and remove Telnet access!" alert="Note" icon="svg-info" color="blue" %} + +ZTE has created various region codes that load default values based on the local ISP. This configuration can be changed using this command: + +```sh +upgradetest sfactoryconf X +``` + +Where X is the number of supported regioncode into file `/etc/init.d/regioncode`, here is an example from TIM `V3.0.10N06` firmware: + +```sh +# cat /etc/init.d/regioncode +14:Thailand +97:ItalyTi +116:Tescali +154:Izzi +163:BrazilClaroHome +188:HollandKpnSfu +198:Manufacture +2074:ItalyFastwebSFU +``` + +# Random notes +- This new ONT (and probably the XGSPON version as well) has Secure Boot enabled. All headers contain an RSA key that is verified by U-Boot and the CPU (for U-Boot itself), so there’s no way to repack the rootfs to make it fully spoofable (at the moment..). +- If your ONT is updated by the OLT (e.g., an F6005v3 OpenFiber ONT connected to a TIM OLT), the U-Boot partition will also be updated. After this update, it will no longer be possible to switch to the other partition because the signatures will not match, and TTL console is muted after U-Boot start. + +# Miscellaneous Links + +- [ZTE ONU Telnet Enabler](https://github.com/stich86/zteOnu) + +# Teardown and other photos + +## HW V3.0 + +{% include image.html file="f6005v3_2.jpg" alt="Top of the F6005v3" caption="Top of the F6005v3" %} +{% include image.html file="f6005v3_3.jpg" alt="Bottom of the F6005v3" caption="Bottom of the F6005v3" %} + +--- + +[^1]: Credentials are randomly generated by ZTE ONU Telnet Enabler, they are not persistent and will change at reboot. +[^2]: Serial console is read-only mode on most of U-Boot, and no output after kernel load. For OF V3.0.10P3N2 is possible after pressing ESC during the boot to access U-Boot Console. diff --git a/_ont/ont-zyxel-pmg3000-d20b.md b/_ont/ont-zyxel-pmg3000-d20b.md index 761baab..b1d4a57 100644 --- a/_ont/ont-zyxel-pmg3000-d20b.md +++ b/_ont/ont-zyxel-pmg3000-d20b.md @@ -49,7 +49,7 @@ The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be a - [Halny HL-GSFP](/ont-halny-hl-gsfp) - [D-LINK DPN-100-Rev-A2](/ont-d-link-dpn-100-rev-a2) -- [Ziza OP151s](/ont-ziza-op151s) +- [Zisa OP151s](/ont-zisa-op151s) - [T&W TW2362H-CDEL](/ont-t-w-tw2362h-cdel) ## List of software versions |