blob: fea2db8dde9e2b08f5dfea039a746877e6b9d219 (
plain) (
tree)
|
|
Heimdall (c) 2010 Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au/products/heimdall/
DISCLAIMER:
This software attempts to flash your Galaxy S device. The very nature of
flashing is dangerous. As with all flashing software, Heimdall has the
potential to damage (brick) your phone if not used carefully. If you're
concerned, don't use this software. Flashing ROMs onto your phone may also
void your warranty. Benjamin Dobell and Glass Echidna are not responsible
for the result of your actions.
These instructions are for OS X operating systems.
Installing Heimdall and Heimdall Frontend Binaries:
1. Run "Heimdall Suite.pkg" and follow the instructions.
2. Reboot your system.
3. Done
Installing Heimdall from Source:
1. First make sure you have installed XCode and pkgconfig.
NOTE: There are several different ways you can install pkgconfig, one
option is to use Macports (http://www.macports.org/).
2. Open a terminal and navigate to the directory where you extracted
Heimdall.
3. Then enter the following commands to compile and install libusb-1.0:
cd libusb-1.0
./configure
make
sudo make install
cd ..
If you have problems please consult http://www.libusb.org/
4. Enter the following commands to compile and install Heimdall:
cd heimdall
./configure
make
sudo make install
cd ..
5. If you haven't installed the driver before, enter the following:
cd OSX
sudo ./install-kext.sh
6. Done
Installing Heimdall Frontend from Source (Optional):
1. First make sure you have installed XCode and Qt 4.6 or above,
available from http://qt.nokia.com/.
2. Open a terminal and navigate to the directory where you extracted
Heimdall.
3. Enter the following commands to compile and install Heimdall Frontend:
cd heimdall-frontend
qmake heimdall-frontend.pro
4. This will produce an XCode project called heimdall-frontend.xcodeproj
in the heimdall-frontend folder. Open this file in XCode.
5. From the menu bar select Build -> Build. This outputs heimdall-frontend
to /Applications
6. Done
Flashing Firmware with Heimdall Frontend:
1. Fully charge your device (use the wall charger as it's faster).
2. Download a decrypted Samsung Galaxy S ROM and extract it to a directory.
3. If the ROM is provided as one of more archives (nested or otherwise),
extract them all to the same location.
NOTE: If you want to use the CSC then extract it last.
3. Open Heimdall Frontend.
4. Put your Galaxy S device into download mode.
5. For each file you wish to flash use "Browse" to select the file.
6. Press "Start".
7. Heimdall Frontend will display the progress and inform you when the
flash is complete.
Flashing Firmware from Command Line / Terminal:
1. Fully charge your device (use the wall charger as it's faster).
2. Download a decrypted Samsung Galaxy S ROM and extract it to a directory.
3. If the ROM is provided as one of more archives (nested or otherwise),
extract them all to the same location.
NOTE: If you want to use the CSC then extract it last.
4. Open a terminal and navigate to the directory where you extracted the
ROM files.
5. Type the following to list all the functionality Heimdall supports:
heimdall help
8. Use the instructions to manually enter a command with all the files you
want to flash.
Here is an example that does a full flash and repartition:
heimdall flash --repartition --pit s1_odin_20100512.pit --factoryfs factoryfs.rfs --cache cache.rfs --dbdata dbdata.rfs --primary-boot boot.bin --secondary-boot Sbl.bin --param param.lfs --kernel zImage --modem modem.bin
9. Done
|
